-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
- Articles
Article Highlights
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Thin PCBs for Smart Phones: Technology and Reliability Considerations
November 19, 2014 |Estimated reading time: 1 minute
Abstract
The next generation of smartphones will demand very thin multilayer boards to reduce product thickness again. This paper shows three different manufacturing approaches which can be used for very thin, any-layer build-ups. The technological approaches are compared on reliability level—the any-layer copper filled microvia technology which is to be considered as state-of-the-art technology for high-end phones and the ALIVH-C/G technology that is well established in Japan.
A test vehicle design featuring test coupons for comprehensive reliability test series has been defined as target application for investigation. The applied test vehicle build-ups comprise an eight-layer build-up with total board thickness below 500 µm. The first test vehicle is based on an any-layer HDI build-up including copper filled stacked microvia structures, the second test vehicle features a 1+6+1 ALIVH-C build-up comprising an outer HDI prepreg layer, while the third test vehicle is built in ALIVH-G technology featuring a full ALIVH build-up.
The influence of the applied manufacturing technology on the reliability performance of thin PCBs is evaluated based on these three test vehicle build-ups.
To cover the behavior during SMD component assembly the produced samples are subjected to reflow sensitivity testing applying a lead-free reflow profile with a peak temperature of +260ºC. Failure occurrence and the observed failure modes are evaluated and compared.
In parallel, a temperature cycling test is conducted on the test vehicles in a temperature range between -40ºC and +125ºC to evaluate the thermo mechanical reliability of the test vehicles with regard to the manufacturing technology.
To characterize the reliability aspects influenced by electrochemical migration phenomenon the different samples are subjected to a HAST test at +130ºC with 85% humidity level.
The results obtained from reliability testing are summarized and compared within this paper. The identified relations between manufacturing technology and the reliability performance of the test vehicles are shown; strengths as well as weaknesses of the applied any-layer technologies are identified and summarized.
Read the full article here.
Editor's Note: This article originally appeared in the October issue of The PCB Magazine.
Suggested Items
TTM Celebrates the Grand Opening of Its First Manufacturing Facility in Penang
04/25/2024 | TTM Technologies, Inc.TTM Technologies, Inc., a leading global manufacturer of technology solutions including mission systems, radio frequency (RF) components and RF microwave/microelectronic assemblies, and quick-turn and technologically advanced printed circuit boards (PCBs), officially opened its first manufacturing plant in Penang, Malaysia with an investment of USD200 million (approximately RM958 million).
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
IPC Design Competition Champion Crowned at IPC APEX EXPO 2024
04/24/2024 | IPCAt IPC APEX EXPO 2024 in Anaheim, California, five competitors squared off to determine who was the best of the best at PCB design.
Real Time with... IPC APEX EXPO 2024: all4-PCB, A Premier Solution Provider for the PCB Industry
04/22/2024 | Real Time with...IPC APEX EXPOIn the PCB industry, all4-PCB, is a top-tier equipment supplier and process solution provider. Ralph Jacobo highlights the active market and the demand for high-quality equipment, discusses their existing customers, investment in advanced substrates, and smaller board shops.